SCCAForums.com

1982 Morton Solo Vee
Will fit large driver (6' 2", 200 lbs) and completely sorted out.
838 lbs.
Less than 3.5 hours since engine rebuild, well prepped.
Zero roll with Carreras all around.
History since new, logbooked until a few years ago.
Always garaged, ran in it last year so it hasn't just been sitting.
Located in Kansas

$6200.00  $6,000  (edit:  see below post for more detail)

Includes car, trailer, ten years worth of spares and parts, multiple
sets of tires and wheels, specialty tools, etc. Pretty much a turn-key
deal - put on your helmet and drive.

No dedicated website but email me if you're interested for specs,
pictures, etc. at dgeis at cox dot net

---

Dave Geis
#25 ss - '07 Z-51
http://wichitascca.org

You should also post this on the classified ad forum at formulavee.org/interchange

---

2002 Mercedes C230k, retired, 2005 Nationals STU DFL

1969 Beach Solo Vee and 1985 Lynx B Solo Vee

PRICE REDUCED to $6000!!!

So what are you getting for that reduced price?

McNamara “clone”, cockpit widened for larger driver (I’m 6’2”, 200 lbs)
Original Logbooks and history since new.
838 lbs
Always garaged
Zero roll rear suspension
Carrera adjustable shocks
¾” front sway bar
½” adjustable rear sway bar
Steering quickened
Belts dated Apr 03, Fuel cell replaced 2-01, new battery 8-05

Engine
1600 cc
Rebuilt Spring 2002, time on engine since rebuild: 3 hr 40 min

New Weber 40IDF installed 5-03

Tires and Wheels
1 set mounted Goodyear R120 on Diamond Racing wheels
1 set mounted Hoosier R25A on Diamond Racing wheels
1 set unmounted “new” Hoosier R25A w/3 laps at HPT
1 set mounted Goodyear FV rain tires on VW wheels
1 set mounted Goodyear FV rain tires on VW wheels (junk for storage)
1 set spare VW wheels

Trailer
1997 PJ Trailers, 6 ½’ x 10’ utility trailer, 5000 lb axle
New tires 9-02
Chrome wheels
New LED lighting
Custom U-channel aluminum ramps
4x 10,000 lb tiedowns
Spare tire
Decking replaced 8-00
Cover for winter storage

Spares
1x Engine block
1x IRS transaxle
1x complete exhaust system
7/16” rear sway bar
9/16” front sway bar
Engine stand
3x large boxes of misc. parts
1x large tool box full of everything from 36mm axle nut socket to extra carb jets
4x scales
2x car stands
Tire balancer w/wide 5 adaptor and weights
2x gas cans
Trickle charger w/quick connect
Misc. VW service manuals & catalogs
Alignment “toe” bar
Longacre 0-30 tire guage
Seat pad for shorter driver
Foam pad for taller driver
_________________
Dave Geis
#25 SS - '07 Z-51

---

Dave Geis
#25 ss - '07 Z-51
http://wichitascca.org

When you say it'll fit a large driver, how large? :)

---

I am Chris Hammond.
Going2Colorado.com

where's the car located?     

Wichita, Kansas.

---

2002 Mercedes C230k, retired, 2005 Nationals STU DFL

1969 Beach Solo Vee and 1985 Lynx B Solo Vee

Sorry for the delay in response. I couldn't log in and had to have a computer ner. . . . ahhhh. . .a good friend come over and see what was wrong ;-).

 

In answer to the questions asked. 6' 2" and 200 lbs is pretty much it. Anything more than that will be above the main-to-front hoop "ruler" check. It's actually quite a bit more than the "normal" formula car.

 

And already answered, it's in Wichita Ks.

---

Dave Geis
#25 ss - '07 Z-51
http://wichitascca.org

Dave G:

...Anything more than that will be above the main-to-front hoop "ruler" check.

That's the rule in club racing.  For Solo, the pertinent rule is in Appendix C - SOLO ROLL BAR STANDARDS
A. BASIC DESIGN CONSIDERATIONS
      2. The top of the roll bar shall not be below the top of the
driver’s helmet when the driver is in normal driving position,
and shall not be more than six inches behind the driver. It is
strongly suggested that the roll bar extend at least three
inches above the driver’s helmet. In case of two driver cars,
both drivers must be within the roll bar height requirement,
however only one driver must be within six inches of the roll
bar. In a closed car equipped with a roll bar/cage, it must be
as close as possible to the interior top of the car.

 

i know it is a long shot, but you wouldn't be interested in a trade for a fourwheeler by chance would you? I have a 2006 yfz 450 i am currently in the process of selling. let me know if it is something you would entertain.